We really want to borrow a bike for photos! If you have a late model CB650R or CBR650R that we can borrow for two days, we'll give you a free seat in exchange. We just need it in our photo studio (Hollister, CA) and won't ride it. Contact us HERE.
For this model we've made our traditional Gunfighter saddle with a bit more passenger capability. This gives your bike clean looks with enhanced 2-up capabilites.
We started with our high density Comfort Cell foam that allows a sleek profile while providing a firm, supportive ride. Then we sculpt the rider seating ergonomically to fit the curve of your body and provide better weight distribution. This also helps to eliminate the centralized pressure felt from the stock seat. In the nose area, we sculpt the saddle narrow to allow for ground reach.
For a clean look, the passenger area is shaped to emulate the lines of the bike with a low profile. On the inside, the tail is padded and upholstered to provide for passenger capability. As we mentioned earlier, this particular Gunfighter saddle was built with a little extra copilot comfort in mind.
Notice how close the Corbin saddle fits to the tank, tail section and sides... this kind of fit comes only from a Corbin saddle and our unique Fibertech basepan. Our rigid base material not only fits perfect to the bike, but provides a firm foundation to support the carefully designed foam shape. Corbin's ergonomic shaping creates a visually pleasing look on the motorcycle and adds to the custom appeal. Over time, our exclusive foam material will break in for a personalized fit to your body.
On top, we include your choice of materials in a wide range of colors and textures. The images above show Charcoal Alcantara seating, Matte Black contrasting sides, Bronze Brushed Aluminum welt, with Copper stitching and Corbin logo to coordinate with the colors on the CB. You can also choose from a range of color options by special order at no additional charge!
We use genuine leather seating and Alcantara in all of our saddle models because it breathes with your body and will conform along with the foam shape during break in. This provides an added bit of luxury on those long rides. In the side panels, we use a coordinating vinyl material that will support the foam shape and keep the saddle looking sharp longer. Be sure to care for a leather saddle properly with a quality conditioner like our Saddle Cream.
Our seat rides on rubber bumpers to protect your paint job and mounts to your bike using the stock key lock system. All required brackets come pre-mounted on the saddle. Rear seat latch is adjustable to assure a perfect fit with your key lock system. When new, you may wish to put a washer between seat and bracket to ease locking on the bike. Remove these washers once the rubber bumpers have broken in a bit.
UNIQUE TECHNOLOGY:
The design and manufacture of Corbin products is so unique that
Mike Corbin himself holds more than 60 United States Patents!
From the process itself to new innovations like the Corbin
Glovebox, you can count on highly functional and unique products
that work. Corbin products are manufactured under one or more of
the following US Patents: 6,848,156 B2; 6,729,516 B2;
D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937;
5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
FIBERTECH™ BASEPAN:
A purpose-built hybrid material that provides a firm foundation
to support the carefully designed ergonomics of the Corbin
saddle. It provides a precision fit to every arc and contour of
the machine and rides on rubber bumpers to protect your paint.
We always design our basepans as flat as possible so bumps or
odd shapes don't telegraph through the foam to your body.
Click the button at left to learn
more...
COMFORT CELL® FOAM:
The heart of the Corbin saddle! Our exclusive, purpose-built
foam material, called Comfort Cell, was created to
provide a firm, resilient ride that doesn't break down. This
means it will support you for long days on the road. Over time,
Comfort Cell will break in to provide a personalized fit to your
posture and even greater comfort!
For the complete story, just click the
button.
ERGONOMIC SHAPING:
A major part of the design criteria of the Corbin saddle is its
ergonomic shape. This means the saddle's foam shape is designed
to emulate the curves of the human body. This provides more
square inches of body contact and helps eliminate hot spots.
This shaping also neutralizes the seating platform to help curb
sliding in the saddle, which reduces fatigue. In a nutshell:
more comfort for a longer ride!
Click the button at left for an animation that shows
how it works.
PATENTED MANUFACTURING TECHNOLOGY:
Always an innovator, Mike Corbin invented Integrated Molding
technology, which is now the process by which all Corbin
saddles are made. This process allows extremely tight
tolerances and creates a chemical bond between the foam and
base material.
To see what this is all about, click the button for
more information.
GENUINE LEATHER:
We use leather in all panels of the seat that contact your body.
This provides a luxurious ride that breathes with your body.
Leather will also break in along with the foam shape to support
a personalized fit. Available in a wide range of textures and
styles to suit your taste.
For more information about leather seating,
click away.
Concerned about how a material will look? We will gladly send
samples at no charge. Visit our
materials page
and use the chatbot to place your request. Limitations apply.
Saddle Cream
Take good care of your new seat and it will take care of you!
Perfect for all your leather goods.
$25
Measurements:
Rider seating: 12" wide x 13" long x 3.5" deep Rear seating: 8" wide x 10" long
Mounts easily with brackets preinstalled on the Corbin saddle that mesh with your stock key lock system. Simply slide the saddle into place nose first to engage the front tongue and lower the rear into place. Push firmly on the tail section to latch and you're ready to hit the road.
Corbin saddles (with very few exceptions) include
Genuine Leather Seating
to provide a luxurious look and feel... don’t let anybody tell you
that vinyl is just as good! You wouldn’t buy vinyl boots, would you?
WARNING:
Heater elements (when available) should never be installed in
motorcycle seats that will be used by riders that cannot sense heat.
This could create a hazardous condition.
Testimonials:
The seat draws an enormous amount of interest. Thanks for everything to you and the entire crew at Corbin, and I really hope you enjoy the pictures. -Mak Happy beyond description
Comments?
Of course we want to hear from you! Have some suggestions for us
or maybe comments for other riders? Send them via
THIS FORM.
Submit Photos:
Showcase your bike on Corbin.com! Use this form to upload photos
for possible inclusion on our website. Ready, set...
LET'S SEE 'EM!
General Contacts
California Factory:
Corbin Saddles
2360 Technology Parkway
Hollister, CA 95023
800-538-7035
Florida Showroom:
Corbin Saddles
1433 North US Highway 1
Ormond Beach, FL 32174
800-223-4332
PLEASE NOTE:
Corbin products are designed to fit very close to your bike for a clean look.
Due to this, other accessories or options can inhibit proper fit. As an example:
Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc.
If you have accessories installed on your bike, please let us know so we can
verify the fit for you.
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount.
CUSTOM COVERS: You are always welcome to choose from our wide variety of colors and material options for your saddle. We provide these options at no extra charge as long as we can use our existing cover patterns. Creating a new cover design requires specialized custom work and will result in additional charges.
SADDLE WARRANTY:
Basepan, foam and hardware of the Corbin saddle is warranted to the original
owner for life. Cover materials, Heaters and workmanship are warranted for
one year. Product will only be authorized to be shipped back for refining of
shape or to replace/rectify defective parts. In cases where the rework requires
a new cover, a recover charge will be applied. Cash or credit refunds are not
available. All goods being handled for customer service consideration must be
accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY:
Structural integrity of Corbin fiberglass components are warranted to the
original owner for life. Finish and paint are warranted against manufacturing
defect for one year. Damage to product and / or painted surfaces from outside
forces or misuse is specifically not covered under warranty. Cash or credit
refunds are not available. All goods being handled for customer service
consideration must be accompanied by a Corbin receipt and a Return Material
Authorization (RMA) number.
EXPORT SALES:
USA pricing shown. When products are shipped throughout the world, you will
see higher prices because of freight, customs, duty & applicable taxes.
Please consider these costs when purchasing Corbin products outside the USA.
If ordering direct from Corbin, we will compute freight charges and add them
to the order. BUYER will be responsible for customs, taxes, duty or other charges.
MILITARY & FIRST RESPONDERS: As a small token of our appreciation for your service to our country, we proudly offer a 10% discount to active military, veterans and first responders. Thank you for what you do! Be sure to notify us when the order is placed, we cannot change orders already in process. Call us at 800-538-7035 so our Reps can apply your discount.