 |
|
This new design Dual Touring Saddle provides you and a passenger with sculpted seating and long range comfort with the luxurious addition of electric seating heaters. Our generously contoured platforms provide better weight distribution to eliminate pressure points and give long range support. This is the perfect saddle setup for touring quality comfort on your new Vegas.
Corbin's Dual Tour accepts two removable rider's backrests! Each backrest is fully adjustable for a tailored fit to rider posture. Use a single backrest and transfer it front to rear as needed or you can order two backrests for full time use in your saddle. Just like our saddles, the Corbin backrest is ergonomically shaped to fit the contour of your body for maximum contact area and support.
In the front we have engineered the backrest to fold down to make it easier to mount the bike. Corbin's backrest hardware is spring loaded to make the rest pop back upright after you throw your leg over. This special hardware (internal to the saddle) also allows the backrest position fore and aft to be adjusted to your profile. This enables the backrest to be completely customized to fit your riding posture (see instructions below).
For the ultimate in luxury, we have built electric seat heaters into our Dual Touring saddle design. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. The two-position switch allows you to select a heat level depending on conditions. The level of heat is controlled automatically by a thermostat built into the control unit. This setup is very simple to install into your Victory Vegas wiring.
Our new Ovalbac style backrest gives a very cool look and a nice ride. As mentioned, the shaping is designed to cradle the arch of your back and give you excellent support without a pressure point on your spine. The Oval cutout means it won't trap heat against your body and makes an excellent hand hold for your passenger while riding or for you while moving your bike in the garage. A variety of finishing plate options are available for the rear of the rest to give a totally customized look.
Dual Touring Saddle also accepts our chrome "V-rail" for an added nostalgic touch. Show quality chrome plating provides a nice touch of class. V-rail mounts directly to the Corbin saddle for simple installation that does not require drilling or brackets. Saddle installation is simple using a tongue in the front and a special bracket in the rear preinstalled on the Corbin saddle.
We use genuine leather in all of our seat models to provide a luxurious ride that breathes with your body. A wide range of leather options is available for a custom look to suit your taste. Leather will break in along with your foam shape to give you a personalized fit and will age gracefully with proper care. Take good care of your leather seat with a quality conditioner like Corbin's Saddle Cream. You seat will look nice for years and show character just like your leather jacket.
Note: the Dual Tour saddle does not work with the stock luggage rack.
|
|
|
|
|
|
 |
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1. |
 |
 |
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button. |
|
 |
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works. |
|
 |
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info |
|
 |
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away. |
|
 |
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more... |
|
 |
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info... |
|
 |
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info... |
|
Measurements |
Rider Seating: 13.5" wide x 17" long
Passenger: 12" wide x 13.5" long
Approx. Seat height: 27"
|
|
|
|
|
|
Measurements: |
Rider Seating: 13.5" wide x 17" long
Passenger: 12" wide x 13.5" long
Approx. Seat height: 27"
|
|
 | Installation Instructions: [Page 1] - [Page 2]
 Dual Touring saddle installs easily on your bike with a tongue in the front and a special fender bracket in the rear. Bracket comes preinstalled on the saddle and is designed to use the stock bolts into the side of your fenders. Saddle comes complete with all wiring and controllers to wire easily into your stock loom.
|
|
|  Driver's backrest fore-aft position can be adjusted easily by replacing a single screw in the backrest hardware. This can be accomplished by folding down the backrest and accessing it under the velcro tag on the saddle. Quick and Easy! |
|
| Note: the Dual Tour saddle does not work with the stock luggage rack. |
|
|
|
|
|
#VR-DT
Chrome V-Rail |
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed.
*More Info*
|
|
#Conditioner
Saddle Cream® |
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application.
*More Info*
|
|
#02-SB
Standard Ovalbac® |
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome!
*More Info*
|
|
#297-SB
Standard Backrest |
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired.
*More Info*
|
|
#02-L
Large Ovalbac® |
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome).
*More Info*
|
|
#02-T
Tee Ovalbac® |
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear.
*More Info*
|
|
#02-G
Gunfighter Ovalbac® |
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear.
*More Info*
|
|
#GB
Gunfighter Backrest® |
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles
*More Info*
|
|
#GLOVE-BOX
Glove Box |
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too!
*More Info*
|
|
|
|
|
|
|
Testimonials: |
|
|
Submit Your Comments |
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM. |
|
General Contacts |
|
|
|
|
|
|
 |
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
|
|
 |
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
|
|
 |
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, Please Read
|
|
 |
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
|
|
|
|
|
|
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available. 
All Corbin saddles (with very little exception) include 
