Corbin has a long history of designing saddles that look as well as they perform and the Hammer Dual Tour is no exception. This saddles offers incredible comfort gains that look good on the bike. Notice how well the saddle fits to the tank and fender groove and provides two large seating buckets that don't overpower the bike visually. We sculpt each seating area for proper weight distribution and allow long range capability. Generously contoured platforms eliminate hot spots and centralized pressure that causes discomfort. On the inside, our exclusive Comfort Cell® foam material gives firm support that conforms to your body.
The Dual Touring Saddle accepts two removable rider's backrests for added back support. Our backrests are fully adjustable to provide a tailored fit to individual's posture. Support hardware is internal to the saddle to keep a clean look without external contraptions. In the front, we've engineered a second adjustment that allows the position of the rest to be adjusted fore/aft. This special hardware also allows the backrest to fold down to ease mounting the bike.
You can use a single backrest that transfers front to back as needed or get two backrests for full time use. Installation is easy enough to make this possible at a moments notice. Simply slide the backrest shaft into the built in hardware and secure it in place with the provided setscrew. There is no need to remove the saddle from the bike for this procedure. Once the backrest is installed, all adjustments can be performed without removing the saddle. Like the saddle, Corbin backrests and sissy bar pads are shaped to fit the curve of your body for a better fit and greater comfort.
The ergonomic design of the Dual Touring saddle also gives a nice flowing shape on the bike for a clean look. Inside the saddle, Corbin's Comfort Cell® foam provides a nice firm perch that supports your body indefinitely and doesn't cave in like softer materials. Comfort Cell Cell® feels firm when you first ride on it, but it is this support that gives you daylong comfort. Notice also, the amount of vertical support offered by the bucket design of the Corbin saddle... over 7" of vertical support or 17" with the backrest installed!
We use genuine leather seating panels for a luxurious ride that breathes with your body. Leather is extremely durable and will break in along with the foam shape to conform to your body. Saddle comes standard in all plain black for a look as tough as the bike itself. Be sure to care for your leather saddle properly with a quality conditioner like our Saddle Cream. This will help the hied to resist the elements and remain supple. The leather seating will conform along with the foam shape and provide a personalized fit to your posterior. Over time, your leather saddle will develop its own unique character just like your leather jacket does.
Corbin's Ovalbac backrest design (shown) has removable finishing plates on the rear that gives you a nice customizing option. Backrests come standard with an ABS plate that gives a leather look, but are also available in a Carbon Fiber or Aluminum look or even primer for custom painting. For a little extra, we can even supply a backing plate that is pre-painted gloss black or even chrome.
If you're looking to add a little storage space to your Hammer how about a cool new glovebox for the rear of your Ovalbac backrest (#02-S only). Designed to carry four liters of your essential stuff like cell phones, spare gloves, bottled water, maps and sunglasses. Constructed of durable ABS and painted gloss black for a perfect finish. You can leave this mounted on your backrest full time or swap it with a regular finishing plate as needed. Installation is just two screws! Comes fully lined and weather stripped with two keys.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
Measurements
Rider Seating: 14" wide x 15" long x 7" deep
Depth w/ backrest: 17"
Passenger: 12.5" wide x 11" long
Measurements:
Rider Seating: 14" wide x 15" long x 7" deep
Depth w/ backrest: 17"
Passenger: 12.5" wide x 11" long
Installation Instructions: [Page 1] Dual Touring saddle installs easily on your bike using existing positions on your bike. All installation hardware is include so your new saddle is ready to go right out of the box.
First install the provided mounting tabs into the fender as shown. Use a little locktite on each bolt and tighten to 8 ft lbs.
Now slide the saddle into position with the tongue in front going into your chassis near the ignition box. Notice we do NOT use the rubber holder on top of the chassis. Lower the rear of the saddle into place and secure to the previously installed brackets. There is a small skirt on the saddle's side to allow access to these bolts. Tighten to 8 ft lbs.
Show your colors! We usually have a new tee shirt design available every year. For 2007, we are offering the Corbin tee with the official Hollister Rally logo on the Front and our pinstripe design on the back. Available in a variety of styles for men and women! *Show Me*
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Product Questions
If you have a specific question about this product, just drop us a line. We strive to answer all e-mail within one business day.
Post Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them HERE.
Install Issues?
Having trouble getting your new seat to mount? Check out our Installation Tips page here: Trouble Shooting
Need replacement brackets, hardware or instructions? Write to us here: Tech Support
Hollister Rally INFO
Thinking of making the trek to the Birthplace of the American Biker for the 60th anniversary? You should! Get the latest information on what's happening and where HERE.
Ordering a seat custom or wondering what that inventory model looks like? This is the place to look for all of the current leather and vinyl materials we offer.
Subscribe to the Corbin Times Home Edition. Our weekly newsletter will keep you up to date on new products, new applications, rallies and more. It's fun to read and members are automatically entered for monthly prizes!
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
ITEM
DESCRIPTION
PRICE
#V-HAM-DT
Dual Touring Saddle
$549
Seating Panels
Side Panels
Welts
Stud Bands
Studs
Stitching
Special Notes
Unless otherwise noted, saddles may be shown with optional items that are not included. See Accessories Tab for Corbin Backrests, V-Rails & other accessory items.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.
