Dual Tour for 1998 - 2005 Road Glide & 1997 - 2005 Electra-Glide
Often imitated, but never duplicated, Corbin's popular Dual Tour is now available for use with a Corbin Passenger Backrest, Chrome V-Rail and optional Seat Heaters. This model provides you and a passenger with the most comfort and support available. Our sculpted seating gives proper weight distribution to allow long range comfort. Generously contoured platforms eliminate hot spots and centralized pressure that causes discomfort. On the inside, Corbin's exclusive Comfort Cell® foam material gives firm support that conforms to your body over time for a personalized fit. Naturally, we keep a nice flowing line on the bike that integrates with the vintage theme.
For riders of varying stature, we have added a "Close" model Dual Touring saddle. This particular seat model has all the features and benefits of the standard Dual Tour, but is built with seating closer to the bars for easier reach. We've also made the nose a bit narrower to give easier ground reach at stop signs. To figure out which model is right for you, just sit on your bike and have a friend measure your seating position relative to the fender screw. Compare this measurement to the illustration and you're ready to go.
This newly designed version of our Dual Touring Saddle accepts two removable rider's backrests. Backrests are fully adjustable for a tailored fit to your posture and install or remove easily as desired. In the front we have engineered the backrest to fold down to make it easier to mount your bike. This special hardware, which is built into the saddle, also allows the backrest position fore and aft to be adjusted to your stature. Once the backrest is installed, both of these adjustments can be performed without removing the saddle from the motorcycle. You can use a single Corbin backrest that transfers front to back as needed or get two backrests for full time use. Installation of the Corbin backrest is easy enough to make this possible at a moments notice. Since the saddle is designed to work with a Corbin backrest in the rear, it will not install properly on your bike if you have either of the Tour Pacs mounted. We have, however, designed the Dual Touring Saddle to work with the "detachable" sissy bar / passenger rest available from Harley-Davidson. We even make a coordinated backrest pad to complete the look (#RK-PAD).
The ergonomic design of the Dual Touring saddle also gives a nice flowing shape on the bike for a clean look. To add to the vintage appeal of the Dual Tour, we've integrated hardware for our Chrome V-Rail. With just four included bolts, our show quality chrome rail bolts directly up to the saddle with no additional hardware. This provides an added bit of flair and really compliments the nostalgic look of the baggers. For a very clean installation, you can also replace your stock seat tab screw with one of our Chromed Billet thumbscrews. A very nice look and tool free installation!
For the ultimate luxury for those early morning rides try our heated seating option. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. The two position switch allows you to select a heat level depending on conditions. Once on, the level of heat is controlled automatically by a thermostat built into the control unit under the saddle. Of course, it is very simple to install into your stock wiring.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Measurements
Rider Seating, standard: 14" wide x 17" long
Rider Seating, CLOSE: 14" wide x 15" long
Passenger: 12" wide x 13.5" long
Measurements:
Rider Seating, standard: 14" wide x 17" long
Rider Seating, CLOSE: 14" wide x 15" long
Passenger: 12" wide x 13.5" long
Dual Touring Saddle installs easily with a tongue in the front and a single screw into your fender at the rear. To simplify installation and add a nice touch, we offer a chromed billet thumbscrew in a variety of thread sizes (optional). Your bagger will use either a 1/4" x 20 or 1/4" x 28 thread.
There are two versions of our Dual Touring saddle. The model on this page is specifically designed for bagger owners who do NOT have a Tour Pac on their motorcycle. If you have an H-D trunk on your bike or are planning on adding one later, please refer to our other Dual Touring model located HERE for Road Glides or HERE for Electra-Glides.
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
With the Corbin EZ-Fill adding oil to your primary is simple. Remove the knurled plug from the inspection cover and pour. It looks great and works just as well (a hallmark of Corbin design). Available for: FX, FL Shovelheads, FLST Softails, FXDWG Dyna Wide-Glide, FXR Models, Roadking, Road-Glide and FLH / FLT models. *More Info*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28
Metric: m5 x .8, m6 x 1.0 or m8 x 1.25
*More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Product Questions
If you have a specific question about this product, just drop us a line. We strive to answer all e-mail within one business day.
Post Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them HERE.
Install Issues?
Having trouble getting your new seat to mount? Check out our Installation Tips page here: Trouble Shooting
Need replacement brackets, hardware or instructions? Write to us here: Tech Support
Hollister Rally INFO
Thinking of making the trek to the Birthplace of the American Biker for the 60th anniversary? You should! Get the latest information on what's happening and where HERE.
Ordering a seat custom or wondering what that inventory model looks like? This is the place to look for all of the current leather and vinyl materials we offer.
Subscribe to the Corbin Times Home Edition. Our weekly newsletter will keep you up to date on new products, new applications, rallies and more. It's fun to read and members are automatically entered for monthly prizes!
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
ITEM
DESCRIPTION
PRICE
#HDFLH97-DT-E-VR
Dual Touring Saddle, No Tour Pak, Heated
$699
#HDFLH97-DT-VR
Dual Touring Saddle, No Tour Pak
$479
#HDFLH97-DT-C-E-VR
Close Dual Touring Saddle, No Tour Pak, Heated
$699
#HDFLH97-DT-C-VR
Close Dual Touring Saddle,No Tour Pak
$479
#02-SB
Ovalbac Leather Backrest (ea)
$229
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available.
Seating Panels
Side Panels
Welts
Stud Bands
Studs
Stitching
Special Notes
All Corbin saddles (with very little exception) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available. 
All Corbin saddles (with very little exception) include 
