 |
|
Corbin's Gunfighter & Lady saddle for the Sprint gives your bike an extreme comfort boost. We've taken the thin stock seat that was built solely for looks and engineered a design that looks good and performs to give you and a passenger long range comfort. As you can see from the photos, our sculpted rider's position provides a much greater area of body contact. In fact, the seating area in the front portion provides over six inches of vertical body support! Naturally both seating areas provide a contour designed to fit the human body and eliminate hot spots for longer riding range.
For your copilot, we offer a removable passenger backrest that gives even more support and a feeling of security. The Corbin backrest is adjustable to provide a tailored fit to your passenger's posture. Installation of the backrest is a snap with a single setscrew locking it into place under the saddle. Once installed, the angle can be set without removing the backrest from the seat. We offer several backrest models that can work in this seat design, but recommend the #02-S shown. This model gives the best combination of looks and functionality on the Sprint.
Ergonomic sculpting provides a better fit to your body and improved weight distribution. Neutralized seating posture curbs the tendency to slide in the saddle, which helps to reduce rider fatigue. Notice how the Corbin design has taken out the downhill posture of the OEM seat. Inside, the seat is built up with our Comfort CellŪ foam to provide a firm supportive ride mile after mile. To aid in ground reach, we've shaved the nose area of the seat narrower than the bucket to allow your legs clearance at stop signs. While riding, just slide back into the bucket for maximum support.
Corbin's seat and backrest combination is designed to install easily on your bike and fit perfectly to the tank and tail section. We include a bracket with a stainless steel latch pin that installs on your bike under the stock Triumph hand rail. Once this bracket is installed, your saddle will mount with a tongue in the front and the built in lock at the rear. Please note that the Corbin backrest must be locked in with the safety screw before you install the saddle on the motorcycle.
Like all Corbin saddles, this model includes genuine leather seating panels for a truly luxurious ride. To tie in nicely with the design of the Triumph we recommend the cover materials shown here which is: Carbon-Fiber laminated leather seating and Asphalt sides with no welt. The new asphalt material shown here looks perfect with the textured powdercoated chassis of the Triumph Sprint making a nice custom addition to your bike. Leather seating provides a perch that breathes with your body and will adapt with the foam shape during break in for a personalized fit. Over time, leather will mature to take on its own unique character, just be sure to care for it properly with a quality conditioner like our Saddle Cream.
To further customize the look of your new saddle, we offer a range of finishing plate options for the OvalbacŪ series backrests. The model shown is covered in the same leather type as the saddle for an integrated look and features a Carbon-Fiber look finishing plate on the rear to add to the racebike theme. We also offer a standard leather look model or a brushed aluminum look if you prefer. Either model finishing plate is included at no extra charge. Please note, the glovebox shown elsewhere on this site does not fit on this bike due to the size of the handrail.
Corbin's Gunfighter & Lady saddle installs simply and looks perfect on the bike. Our custom cover materials provide a classy, custom touch while the seat shaping improves the overall ergonomics for a more comfortable ride. Our unique basepan material molds to every contour of the Sprint and fits close to the body grove for clean looks. Underneath, the Corbin basepan rides on rubber bumpers to protect your paint job.
|
|
|
|
|
|
 |
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1. |
 |
 |
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button. |
|
 |
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works. |
|
 |
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info |
|
 |
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away. |
|
 |
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more... |
|
 |
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info... |
|
 |
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button. |
|
Measurements |
Rider seating: 12" wide x 12 long x 6.5" deep
Passenger: 11" wide x 10" long
Approx seat height: 31.5" |
|
|
|
|
|
Measurements: |
Rider seating: 12" wide x 12 long x 6.5" deep
Passenger: 11" wide x 10" long
Approx seat height: 31.5" |
|
 | Installation Instructions: T-ST-1050-GL |
|
|  Installation: Corbin's Gunfighter & Lady saddle includes a special latch bracket that enables your saddle to install or remove on a built in key lock system for ease of use. |
|
|  Just mount this bracket under your handrail as shown and secure with the stock screws. Now slide the saddle into place securing the front of the saddle with the nose tongue and lower the rear of the saddle onto the latch pin. To remove, just insert the key, turn it and lift off the saddle... easy! |
|
| On this model, you must secure the backrest in place with the included safety screw BEFORE you mount the seat on the motorcycle. |
|
| Our new Glovebox design for the #02-S ovalbac backrests will not work on this seat model due to the height of the Triumph handrail. |
|
| The Gunfighter and Lady will work with Triumph Bags. |
|
|
|
|
|
#Conditioner
Saddle Cream® |
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application.
*More Info*
|
|
#02-SB
Standard Ovalbac® |
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome!
*More Info*
|
|
#297-SB
Standard Backrest |
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired.
*More Info*
|
|
#02-L
Large Ovalbac® |
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome).
*More Info*
|
|
#02-T
Tee Ovalbac® |
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear.
*More Info*
|
|
#02-G
Gunfighter Ovalbac® |
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear.
*More Info*
|
|
#GB
Gunfighter Backrest® |
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles
*More Info*
|
|
#GLOVE-BOX
Glove Box |
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too!
*More Info*
|
|
SPECIAL NOTE |
Due to the angle of the tail section, the Corbin glovebox does not work on this seat model. |
|
|
|
|
|
Testimonials: |
|
|
Submit Your Comments |
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM. |
|
General Contacts |
|
|
|
|
|
|
 |
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
|
|
 |
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
|
|
 |
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, Please Read
|
|
 |
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
|
|
|
|
|
|
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available. 
All Corbin saddles (with very little exception) include 
