 |
|
Corbin's extremely popular Beetle Bags are sculpted specially to fit close to the bike for improved weight handling and to be aerodynamically silent. The flowing shape provides a bit of vintage Hot Rod styling to the bike and integrates the rear end into a more precise design. Both bags feature top loading so that contents can't spill out when opened and they will self close in the wind if forgotten. Designed by the same folks that ran Suzuki Hayabusa saddlebags over 180mph on the Bonneville Salt Flats!
Corbin Beetle Bags mold around the passenger's legs to maximize capacity without creating an overbearing look on your sleek machine. We mold the interior wall close to the profile of the bike to keep them narrow and carry the shape around the rear fender. This also carries the weight of the bags and contents closer to the centerline of the bike for a good center of gravity. When loaded properly, you won't even know they're back there while riding and the bike remains stable at all speeds.
Notice how the Corbin mounting system keeps the Beetle Bags close to the bike. We mold them around the fender rails and in tight to the fender. Again, this allows the bags to carry weight in close where it won't upset your balance. This mounting system and design also keeps a narrower profile for best possible aerodynamics and less width to worry about when lane splitting. The blue bike on this page is using a set of 3" shotgun pipes from Hardkrome (part number: 45-8850B) that look really nice as you can see in the top image. Corbin saddlebags will work equally well with your stock pipes, but we can't say the same for ALL after-market pipes. Any system the same height or lower than stock should be fine.
Both bags come completely lined to protect your cargo and feature locking doors for security. Sure seal weather stripping and adjustable lock mechanism keeps them watertight. Our top loading design assures that contents won't spill out when the bag is opened while the forward hinge action allows the bag to self-close if forgotten. Corbin's Beetle Bags come pre-painted to coordinate with your factory paint job so they're ready to install right out of the box.
When loading items inside the bags, it is best to load heavy items closest to the bike for proper load bearing and balance. Also, because of the beautiful painted finish, it is important to load items like disk locks carefully. If you throw an item like this into one of the bags, it can create pressure cracks in the paint on the outside of the bag. Just place items in carefully and, when possible, pack around them to stop items from jumping around if you run onto some rough roads.
Manufactured of our durable Fibertech material, Beetle Bags come as a complete set with all installation brackets and complete instructions included. These bags will fit with Kawasaki sissybar or Corbin Streamliner trunk. We modified the design of our Fleetliner Bags with small spaces which allow the mounting of the sissybar. If you take passengers regularly and are looking for a backrest option, the Corbin Dual Touring saddle may be just the ticket.
|
|
|
 |
 |
 |
Measurements: |
Capacity: 33.4 liters per side
Overall width: 33 inches
|
 |
 | Installation Instructions: kv-2-brkt-bag |
 |
 | Beetle Bags work with your stock exhaust system or the killer shotgun pipes from Hardkrome shown at top. Other aftermarket systems may work as well. |
|
|
 |
 |
 |
Testimonials: |
|
 |
Submit Your Comments |
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM. |
 |
General Contacts |
|
|
|
 |
 |
 |
 |
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
|
 |
 |
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
|
 |
 |
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, Please Read
|
 |
 |
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.
|
|
|
 |
 |
|