Dual Touring Saddle provides you and a passenger with sculpted seating and long range comfort with the luxurious option of electric seating heaters. Our generously contoured platforms provide better weight distribution to eliminate pressure points and give excellent support through the use of our high density Comfort Cell foam. Naturally, all of this comfort is wrapped up in a package that looks great on your Sporty and fits perfect. Lots of custom options help make your bike a one-of-a-kind.
Corbin's Dual Touring seat accepts two removable rider's backrests for maximum back support. Each backrest is fully adjustable for a tailored fit to rider posture. You can use a single backrest and transfer it front to rear as needed or you can order two backrests for full time use in your saddle. In the rider's area we have built in hardware that allows the backrest to be positioned fore and aft depending on your stature. This hardware also allows the backrest to be folded down to ease mounting the bike. Spring loaded design pops the backrest back into the upright position.
For the ultimate in touring luxury, we have built electric seat heaters into our Dual Touring saddle design. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. Corbin's tasteful Sharp Deco stitch (shown) provides a nice custom look and conceals the heater pads built into the saddle. If you order your Dual Tour without heaters, the stitch pattern is not required.
Along the side, the two position switch allows you to select a heat level depending on current conditions. The level of heat is controlled automatically by a thermostat built into the control unit located under the saddle. Heating units, thermostats and controller is all pre-installed on the saddle, making this setup is very simple to install into your Harley. Naturally, we include the pigtail adapter to hook up to your stock fusebox.
Dual Tour also accepts a chrome "V-rail" for an added nostalgic touch. Show quality chrome plating provides a nice touch of class. V-rail mounts directly to the Corbin saddle for simple installation that does not require drilling or brackets. To simplify mounting the saddle on your bike and provide a nice clean look, we also offer a chromed, billet thumbscrew (shown). Our thumbscrew gives tool-free installation of your new saddle and comes in either 1/4 x 20 or 1/4 x 28 thread sizes. Your 2004 Sporty uses 1/4 x 20 for the seat mount, but you may find other uses for these thumbscrews as well.
We use genuine leather in all of our seat models to provide a luxurious ride that breathes with your body. We offer many styles of leather to choose from at no extra charge for a bit more character. Leather is very durable and will break in along with your foam shape to give you a personalized fit. Take good care of your leather seat with a quality conditioner like Corbin's Saddle Cream to help it age gracefully.
As a final custom touch for your machine, Corbin's Ovalbac style backrests (shown) have a variety of backing plate options. Backrests come standard with a black finishing plate that resembles the texture of leather. We also offer the options of an aluminum look, Carbon Fiber look or paintable if you'd like to have it matched to your paint job. For a little extra, you can even order one pre-painted gloss black.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Measurements
Rider Seating: 12.5"wide x 16" long Passenger: 11.5"wide x 8" long
Measurements:
Rider Seating: 12.5"wide x 16" long Passenger: 11.5"wide x 8" long
Installation of the Corbin saddle is simple. Our electric heat system is built into the saddle and wires into your fusebox with included adapters. Saddle is installed with a tongue in the front and a single screw into your fender at the rear. This model includes two different rear brackets to allow fitment onto models with the Bobtail fender.
Rider's backrest position can be adjusted fore and aft to adjust to your stature. Simply fold the backrest down and replace the security screw through the top flap with the appropriate size for the position desired. Complete instructions and screw kit is included.
Corbin's Dual Touring saddle will not work with the stock Harley Davidson sissy bar. The sissy bar limited passenger seating area, so we opted to design for Corbin's Ovalbac® backrest use instead.
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28
Metric: m5 x .8, m6 x 1.0 or m8 x 1.25
*More Info*
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Testimonials:
Submit Your Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
General Contacts
Hollister Factory:
2360 Technology Parkway Hollister, CA 95023 800-538-7035
Daytona Showroom:
1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
ITEM
DESCRIPTION
PRICE
#HD-XL-CU-4-DT-E
Dual Tour saddle w/ Heater, Sportster Custom
$699
#HD-XL-CU-4-DT
Dual Tour saddle no heater, Sportster Custom
$479
#02-SB
Ovalbac Leather Backrest (ea)
$229
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available.
Seating Panels
Side Panels
Welts
Stud Bands
Studs
Stitching
Special Notes
All Corbin saddles (with very little exception) include Genuine Leather Seating to provide a luxurious look and feel.... don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.
If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available. 
All Corbin saddles (with very little exception) include 
