Standard Corbin Dual Touring saddle is shown above. The model number listed on this page is designed specially to work with the chrome dash panel on the CVO Springer Softail.

Designed specially for Softails with the wider fender and 200 series tire on the back. Insist on a geniune Corbin saddle to improve the comfort and looks of your new bike. Our Dual Touring saddle is just what you need to maximize the long range capabilities of your Softail with enhanced comfort for two. Our ergonomically shaped seating gives you massive support for the long haul. The only reason you'll find for stopping is the need for fuel.

Designed to work with the H-D Detachable sissy bar in the rear or with the Corbin backrest system (V-rail will not work with sissy bar installed. ) Corbin backrests are supported by internal hardware for a very clean look and simple, one-bolt installation. You can order a single backrest and transfer it front to back as needed or get two for full time use. Backrest angle adjusts to provide a personalized fit to rider posture in both positions. In the front position, our special hardware allows positioning of the backrest fore & aft for riders of different stature. This special hardware also features a fold down action to ease mounting the bike. With backrest installed, the rider bucket offers 19 inches of vertical support!

Notice how both seating platforms are sculpted to fit the shape of the human body. This is what we call "ergonomic" design and it is one of the critical features of the Corbin saddle. Wide, dished platforms create more square inches of body contact and longer lasting support without hot spots. Inside, our exclusive Comfort Cell foam provides a firm, resilient ride that lasts. Over time, Comfort Cell will adapt to your body and provide a personalized fit for even greater comfort.

As with most Corbin saddles, this model uses genuine leather seating panels for a ride that breathes with your body. Luxurious and durable, leather will provide comfort for many years and will break in along with the foam shape for a personalized fit to your posture. Available decorated to your taste from plain to elaborate. We show it here in plain black, black with studs and black with studs and stitching. For a little extra add electric heat (see below) or a chrome V-Rail to add to the nostalgic appeal.

For those chilly morning rides we offer an option of heated rider seating. We incorporate a heater unit under the leather seating and a switch on the left side of the saddle (so you can turn it on without removing your hand from the throttle). Just flip the switch to the low or high position and the seat will warm up and maintain temperature automatically through an integrated controller. Corbin's heater comes completely pre installed in the saddle and you need only integrate the included pigtail to your fuse box.

Notice how the saddle is designed to fit perfectly to the tank, chassis and fender... Corbin's Wizards have mastered where the leather meets the metal. This kind of fit is available only in genuine Corbin saddles through our patented Integrated Molding system. This process allows us to engineer extremely tight tolerances and fit complex shapes like the beautiful, flowing HD fender. Don't get fooled into thinking a seat designed for last year's model is going to fit properly!

Need more options? Our #02-S model backrests have removable finishing plates on the rear available in a range of styles. The standard plate is an ABS leather look, but we can also provide one with a carbon-fiber look or primer and ready for your custom painter. For just a little extra, we can provide the finishing plate on your backrest prepainted gloss black or with chromed steel like the ones we show here. These make a perfect finishing touch.

Installation is simple with a tongue in the front and a single bolt into your fender at the rear. For a very clean installation that requires no tools, we offer a chromed billet thumbscrew (#ACST-20). Just slide the saddle into place nose-first and tie down the rear into the stock location in your fender. Our optional chrome V-Rail bolts up directly to mounts internal to the Corbin saddle for simple installation and a very clean look. If you opt for electric heat, the saddle will include a pigtail wire that integrates directly with your Harley fuse box (complete instructions included).

Specially designed to fit perfect on the new 2006 Softail models, notice how closely the Dual Touring saddle matches up to the Harley tank. We have also specially sculpted the nose of the saddle to make it narrower and allow an easier reach to the ground. Smaller riders mearly slide forward and out of the bucket slightly to have better ground reach at stop signs and in parking lots. Yet long range riding comfort is maintained with a wide, generous bucket to support your posterior.

Look for that Corbin tag to assure comfort, style and value! There's a lot of motorcycle seat makers out there nowadays, but only one Corbin. Using only the highest quality components like cast Comfort Cell foam and genuine leather seating along with design experience approaching four decades, the Corbin saddle is considered the finest in the world. Available directly from Corbin or your favorite neighborhood motorcycle dealer.

	UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
	FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. We always design our basepans as flat as possible so bumps or odd shapes don't telegraph through the foam to your body. Click on the button at left to learn more...
	COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
	ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
	PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
	GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
	CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
	ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
	Warning! Heater elements should never be installed in motorcycle seats used by riders that cannot sense heat.

Measurements:	Rider Seating: 14" wide x 16" long Back support w/ backrest: 19" Back support w/o backrest: 8" Passenger: 12" wide x 12" long Back support w/ backrest: 10" STOCK unladen seat height: 27.3" CORBIN unladen seat height: 26"
Installation:	[Page 1 - Page 2]
	Installation: The Corbin Dual Touring Saddle installs on your bike like stock using a tongue in the front and a single screw into your fender at the rear. Chrome V-Rail bolts directly to the saddle and doesn't require any outside brackets for installation... very clean!
	Seat heater assembly comes preinstalled on the saddle and ready to go. We supply the wiring pigtail and adapter to connect the seat directly into your stock Harley fusebox. This is a simple procedure that can be handled by virtually any home mechanic.
	Our saddles for the 07 CVO's Softails will NOT fit with the Harley chromed dash panel models: 71283-01 / 71202-03.
	If the main fuse is in the way of installing the bracket, shift it over the battery. The basepan will have a small groove allowing space for the fuse. Shown in the image to the right, move the fuse from point "A" to point "B".
	Designed specifically for the 2008 CVO Springer Softail model.

#Conditioner Saddle Cream®	Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
#ACST Billet Thumbscrew	Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes: SAE: 1/4" x 20 or 1/4" x 28 Metric: m5 x .8, m6 x 1.0 or m8 x 1.25 *More Info*
#VR-DT Chrome V-Rail	Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
#02-SB Standard Ovalbac®	Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
#297-SB Standard Backrest	The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
#02-L Large Ovalbac®	Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
#02-T Tee Ovalbac®	This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
#02-G Gunfighter Ovalbac®	If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
#GB Gunfighter Backrest®	All the functionality of an adjustable backrest, combined with the smallest profile possible. This model is often used as a rider's backrest in Gunfighter seat models just like the #02-G shown above. Includes genuine leather seating and color coordinating options just like our saddles *More Info*
#GLOVE-BOX Glove Box	A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*

Testimonials:
Submit Your Comments	Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them via THIS FORM.
General Contacts	Hollister Factory: 2360 Technology Parkway Hollister, CA 95023 800-538-7035 Daytona Showroom: 1433 North US HWY 1 Ormond Beach, FL 32174 800-223-4332 General Mailboxes Hollister Factory Florida Showroom Online Service Center

Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.

	ITEM	DESCRIPTION	PRICE
	#HD-ST8-CVO-DT-E	Dual Touring Saddle w/ Heater, 2008 CVO Springer Softail	$699
	#HD-ST8-CVO-DT	Dual Touring Saddle no heater, 2008 CVO Springer Softail	$549
	#02-SB	Ovalbac Leather Backrest (ea)	$229
	If you prefer to choose a different backrest model than the #02-SB, just click on the Accessories Tab above. You will be shown all of the Corbin backrest models currently available.
	Seating Panels	Black Leather Asphalt vinyl Black Vinyl Black 'Alligator' (baby) Black 'Alligator' (large) Black Carbon-Fiber leather Black Carbon-Fiber, hi-gloss Black Carbon-Fiber vinyl Black 'Ostrich' leather Black 'Shark' leather Black 'Snake' Blue Carbon-Fiber vinyl Bomber Jacket leather Bomber Jacket BLACK Brown 'Alligator' leather Burgundy vinyl Carbonium Charcoal Gray vinyl Charcoal Carbon-Fiber vinyl Charcoal 'Snake' leather Chocolate Brown leather Classic (Basketweave) leather Candy Red vinyl Emerald Green vinyl Forest Green vinyl Ghost Gray vinyl Goldenrod vinyl Gray leather Gray Partner's leather Gray Partner's vinyl Gray 'Ostrich' leather Gray 'Snake' leather Harley Blue vinyl Interceptor Blue vinyl KTM Orange vinyl Lavender vinyl Ninja Red vinyl Navy Blue leather Orange vinyl Otter Brown vinyl Oxblood vinyl Pigeon Gray vinyl Plum vinyl R-80 Red vinyl Red Carbon-Fiber vinyl Royal Blue vinyl Silver Carbon-Fiber vinyl Sky Blue vinyl Smoke Gray vinyl Tan leather Tan 'Baby Alligator' Tan 'Ostrich' leather Taupe vinyl Teal vinyl Tomato Red vinyl White vinyl Yamaha Charcoal Yellow Yellow Carbon-Fiber
	Side Panels	Black Asphalt Black 'Alligator' (baby) Black 'Alligator' (large) Black Carbon-Fiber Black Carbon-Fiber, hi-gloss Black 'Ostrich' Black 'Snake' Black 'Shark' Blue Carbon-Fiber Bomber Jacket Bomber Jacket BLACK Brown 'Alligator' Burgundy Carbonium Charcoal Gray Charcoal Carbon-Fiber Charcoal 'Snake' Chocolate Brown Classic (Basketweave) Candy Red Emerald Green Forest Green Ghost Gray Goldenrod Gray leather Gray Partner's Gray 'Ostrich' Gray 'Snake' Harley Blue Interceptor Blue KTM Orange Lavender Ninja Red Navy Blue Orange Otter Brown Oxblood Pigeon Gray R-80 Red Red Carbon-Fiber Royal Blue Silver Carbon-Fiber Sky Blue Smoke Gray Tan leather Tan 'Baby Alligator' Tan 'Ostrich' Taupe Teal Tomato Red White Yamaha Charcoal Yellow Yellow Carbon-Fiber
	Welts	Black No Welts Asphalt Black 'Alligator' (baby) Black 'Alligator' (large) Black Braid Black Carbon-Fiber Black Carbon-Fiber, hi-gloss Black 'Ostrich' Black 'Snake' Black 'Shark' Blue Carbon-Fiber Bomber Jacket Bomber Jacket BLACK Brown 'Alligator' Burgundy Carbonium Charcoal Gray Charcoal Carbon-Fiber Charcoal 'Snake' Chocolate Brown Classic (Basketweave) Candy Red Emerald Green Forest Green Ghost Gray Goldenrod Gray leather Gray Partner's Gray 'Ostrich' Gray 'Snake' Harley Blue Interceptor Blue KTM Orange Lavender Lime Green Ninja Red Navy Blue Orange Otter Brown Oxblood Pigeon Gray R-80 Red Red Carbon-Fiber Royal Blue Silver Carbon-Fiber Sky Blue Smoke Gray Tan leather Tan 'Baby Alligator' Tan 'Ostrich' Taupe Teal Tomato Red White Yamaha Charcoal Yellow Yellow Carbon-Fiber
	Stud Bands	Black Asphalt Black 'Alligator' (baby) Black 'Alligator' (large) Black Carbon-Fiber Black Carbon-Fiber, hi-gloss Black 'Ostrich' Black 'Snake' Black 'Shark' Blue Carbon-Fiber Bomber Jacket Bomber Jacket BLACK Brown 'Alligator' Burgundy Carbonium Charcoal Gray Charcoal Carbon-Fiber Charcoal 'Snake' Chocolate Brown Classic (Basketweave) Candy Red Emerald Green Forest Green Ghost Gray Goldenrod Gray leather Gray Partner's Gray 'Ostrich' Gray 'Snake' Harley Blue Interceptor Blue KTM Orange Lavender Ninja Red Navy Blue Orange Otter Brown Oxblood Pigeon Gray R-80 Red Red Carbon-Fiber Royal Blue Silver Carbon-Fiber Sky Blue Smoke Gray Tan leather Tan 'Baby Alligator' Tan 'Ostrich' Taupe Teal Tomato Red White Yamaha Charcoal Yellow Yellow Carbon-Fiber
	Studs	No Studs Chrome Studs Black Studs
	Special Notes

	All Corbin saddles (with very little exception) include Genuine Leather Seating to provide a luxurious look and feel....   don't let anybody tell you that vinyl is just as good! You wouldn't buy vinyl boots would you?
	Warning! Heater elements (when available) should never be installed in motorcycle seats used by riders that cannot sense heat.

   

	PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
	SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials, Heaters and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
	FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number. A note about paint color matching, Please Read
	EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA. If ordering direct from Corbin, we will compute freight charges and add them to the order. BUYER will be responsible for customs, taxes, duty or other charges.