Our Dual Touring Saddle provides you and a passenger with sculpted seating and long range comfort with the luxurious option of electric seating heaters. Our generously contoured platforms provide better weight distribution to eliminate pressure points and give excellent support. Designed to work on all Dyna-Glide models (except Wide-Glide) with dual Corbin backrests or with your Harley-Davidson Sissy Bar... We even have a coordinated sissy bar pad to complete the look!
Corbin's Dual Touring saddle accepts two removable rider's backrests for maximum back support. Each backrest is fully adjustable for a tailored fit to rider posture. You can use a single backrest and transfer it front to rear as needed or you can order two backrests for full time use in your saddle. We offer several styles of backrest to suit your taste, but recommend the Ovalbac model #02-S shown here. This models provides the perfect blend of form and function.
In the front position, we have built in special hardware that allows for the backrest position to be adjusted fore and aft to provide for riders of different stature. This special hardware is also designed to allow the backrest to fold down out of the way to make it easier to mount your bike. Spring loaded hardware pops the backrest back up into position when you're seated. A very clean totally internal system!
For the ultimate in luxury, we have the option of built in electric seat heaters in our Dual Touring saddle. A single switch controls the heat for both the rider and passenger positions. The switch is conveniently located along the left side of the saddle so you can reach it without taking your hand off the throttle. The two position switch allows you to select a heat level depending on conditions. The level of heat is controlled automatically by a thermostat built into the control unit. This setup is very simple to install into your Harley wiring.
Corbin's Dual Touring Saddle also accepts our chrome "V-rail" for an added nostalgic touch, but not if you are using a sissy bar. Show quality chrome plating provides a nice touch of class. V-rail mounts directly to the Corbin saddle for simple installation that does not require drilling or brackets. To simplify mounting the saddle on your bike and provide a nice clean look, we also offer a chromed, billet thumbscrew. Available in either 1/4" x 20 or 1/4" x 28 thread sizes, our thumbscrew gives tool-free installation of your new saddle. You will also probably notice the cool chrome finishing plate on the rear of the Ovalbac backrest... this is a brand new option available for your Corbin backrest!
We use genuine leather in all of our seat models to provide a luxurious ride that breathes with your body. The Corbin backrests adjust to you and your passenger's posture as needed for personalized fit. A wide range of leather options are available for a custom look to suit your taste.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
ELECTRIC HEAT: As an option we can include electric heat in this saddle! This option provides a true bit of luxury for when the temperature starts to drop. Simple to install with major components pre-built into the saddle. Just wire in the included pigtail and you're ready to roll. Click the button at left for complete info...
Measurements
Rider Seating: 13"wide x 16.5" long
Passenger: 10.75"wide x 9" long
Approx. seat height: 28"
Measurements:
Rider Seating: 13"wide x 16.5" long
Passenger: 10.75"wide x 9" long
Approx. seat height: 28"
Install Instructions: [ Page 1 ] [ Page 2 ] Installation of the Corbin saddle is simple. Our electric heat system is built into the saddle and wires into your fusebox with included adapters. Saddle is installed with a tongue in the front and a single screw into your fender at the rear.
Rider's backrest position can be adjusted fore and aft to adjust to your stature. Simply fold the backrest down as shown and replace the security screw through the top flap with the appropriate size for the position desired. Complete instructions and screw kit is included.
Show your colors! We usually have a new tee shirt design available every year. For 2007, we are offering the Corbin tee with the official Hollister Rally logo on the Front and our pinstripe design on the back. Available in a variety of styles for men and women! *Show Me*
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
Corbin's Chrome V-Rail bolts up easily to your Dual Tour saddle with no additional brackets. Triple-plate chromed for a show quality finish, the V-Rail provides a nice nostalgic look for your bike. Does not work with Sissy Bars installed. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Makes seat installation and removal a tool-free snap! Machined billet thumbscrew is polished and chromed for a very clean look. Available in the following sizes:
SAE: 1/4" x 20 or 1/4" x 28
Metric: m5 x .8, m6 x 1.0 or m8 x 1.25
*More Info*
Our Touring sissy bar pad is dished to provide maximum contact area and total support. * More Info*
Product Questions
If you have a specific question about this product, just drop us a line. We strive to answer all e-mail within one business day.
Post Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them HERE.
Install Issues?
Having trouble getting your new seat to mount? Check out our Installation Tips page here: Trouble Shooting
Need replacement brackets, hardware or instructions? Write to us here: Tech Support
Hollister Rally INFO
Thinking of making the trek to the Birthplace of the American Biker for the 60th anniversary? You should! Get the latest information on what's happening and where HERE.
Ordering a seat custom or wondering what that inventory model looks like? This is the place to look for all of the current leather and vinyl materials we offer.
Subscribe to the Corbin Times Home Edition. Our weekly newsletter will keep you up to date on new products, new applications, rallies and more. It's fun to read and members are automatically entered for monthly prizes!
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
ITEM
DESCRIPTION
PRICE
#HD-DYNA-4-DT-E
Dual Touring Saddle, Heated
$699
#HD-DYNA-4-DT
Dual Touring Saddle, not Heated
$549
Seating Panels
Side Panels
Welts
Stud Bands
Studs
Stitching
Special Notes
Unless otherwise noted, saddles may be shown with optional items that are not included. See Accessories Tab for Corbin Backrests, V-Rails & other accessory items.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.
