Gambler saddle offers a sleek, flowing appearance and low profile design that has made this design extremely popular for 'round town cruising. Gambler features a comfortable driver's position with a clean pillion seating area providing a flawless profile. Built-up of Comfort Cell® foam that allows a low saddle that retains comfort value. Sculpted seating disperses rider's weight ergonomically and gives you lasting support while still providing good ground reach at stop signs! This is a good choice for riders that often ride solo or have passengers along for short to medium range trips.
As shown in the images above, the new Corbin CVO cover kit comes pre-set with genuine leather seating. The pre-set CVO cover kit for Gambler seat uses a black ostrich stripe, mercedes leather seating with smooth black sides. Be sure to care for your saddle properly with a quality leather conditioner like our Saddle Cream. Your leather saddle will break in gracefully and develop a unique character of its own... just like your leather jacket.
As with all Corbin saddle designs, we sculpt the rider's area to conform to the shape of the human body. This gives you more square inches of body contact which, in turn, gives better weight distribution. The Corbin saddle eliminates hot spots and increases your riding time... even with such a low profile. Passenger seating area is built mostly to keep a slick look, but the use of our high-density Comfort Cell foam still provides reasonable comfort. From this side, you can also see our new key-lock mounting system used on the Gambler design.
Harley-Davidson also offers a variety of luggage rack and passenger backrest options for your Bagger. Corbin's Gambler saddle will work along with these options with the passenger pads available from Harley or with a coordinated pad of our own making. There are two different trunk sizes available (King Tour Pac shown) and a detachable sissy bar that all fit with this seat model. Naturally we make a coordinating backrest pad for all of these options.
Foam density is an important factor in long range comfort and we always say... "Firm is a good thing". Corbin uses a very unique formula of purpose built materials in the manufacturing process. Combine this with the years of design experience and you have the world's finest motorcycle seat. Comfort Cell® foam combined with our patented molding process deliver unmatched contoured support. Corbin saddles feel firm when you first ride on them, but will break in and adapt to your body and support you in comfort for years to come.
Note: This seat will NOT fit with the CVO trunk and Amp
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button.
Measurements
Rider Seating: Approx. 12.5" wide x 21" long
Passenger Seating: Approx. 7.5" wide x 12" long
Seat Height: Approx. 27"
Measurements:
Rider Seating: Approx. 12.5" wide x 21" long
Passenger Seating: Approx. 7.5" wide x 12" long
Seat height: Approx. 27"
Installation: Corbin's Gambler saddle uses a new key lock system for installation. We include a bracket with stainless steel latch pin that integrates with a lock mechanism on the Corbin saddle. Note: This seat will NOT fit with the CVO trunk and Amp
Start by installing the supplied latch pin bracket by removing the torx bolt that is securing the rear gas tank bracket. Put the latch pin on top of the tank bracket while at the same time lining up the 1" x 1/2" metal block keeper into the small rectangle hole of the chassis. Once the bracket is in place, twist the keeper so the length of the keeper is opposite of the hole and anchors to the chassis with the beveled steps in the keeper. As you snug the allen bolt in, make sure it is well anchored. Once the keeper is in place, line up the rear hole of the bracket with the gas tank tab hole, chassis and resecure using the stock torx bolt. Tighten every thing up to 12 ft. lbs.
The seat installs by screwing the supplied latch pin and nylon cap into the rear thread nut of the rear fender. Slide the key way bracket on the seat into the latch pin on the fender and secure the front of the seat by lining the key lock at the front of the seat to the latch pin on the bracket. Push down on the nose of the seat until you hear TWO clicks.
NOTE: To ease installation until the rubber bumper on the basepan break in, it may be necessary to add a washer between the seatpan and latch bracket. This will make it easier to latch.
Show your colors! We usually have a new tee shirt design available every year. For 2007, we are offering the Corbin tee with the official Hollister Rally logo on the Front and our pinstripe design on the back. Available in a variety of styles for men and women! *Show Me*
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Corbin makes a variety of trunk pads for your co-pilot's touring pleasure. Each model comes coordinated to your saddle design for a totally integrated look.
* More Info*
Product Questions
If you have a specific question about this product, just drop us a line. We strive to answer all e-mail within one business day.
Post Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them HERE.
Install Issues?
Having trouble getting your new seat to mount? Check out our Installation Tips page here: Trouble Shooting
Need replacement brackets, hardware or instructions? Write to us here: Tech Support
Hollister Rally INFO
Thinking of making the trek to the Birthplace of the American Biker for the 60th anniversary? You should! Get the latest information on what's happening and where HERE.
Ordering a seat custom or wondering what that inventory model looks like? This is the place to look for all of the current leather and vinyl materials we offer.
Subscribe to the Corbin Times Home Edition. Our weekly newsletter will keep you up to date on new products, new applications, rallies and more. It's fun to read and members are automatically entered for monthly prizes!
As shown in the images above, the new Corbin CVO cover kit comes pre-set with genuine leather seating. This pre-set CVO cover kit for Gambler seat uses a black ostrich stripe, mercedes leather seating with smooth black sides.
 
ITEM
DESCRIPTION
PRICE
#HDFLH-7-CVO-GAM
Gambler Saddle, 2007 FLH-CVO
$439
 
 
Unless otherwise noted, saddles may be shown with optional items that are not included. See Accessories Tab for Corbin Backrests, V-Rails & other accessory items.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.