Stinger saddle for 2004 Harley-Davidson CVO Electra-Glide
A very cool solo option for your Screaming Eagle bagger. Corbin's Stinger seat design offers excellent rider support and a sleek fastback tail section that hugs the fender. We've designed the seating area ergonomically to provide more square inches of body contact for proper weight distribution. This helps to eliminate hot spots and give you long lasting support in the saddle. Our bucket design of the saddle sits you down into the chassis for better balance and a more natural riding position on the bike. Corbin's built up tail section looks cool and provides good back support to the rider... especially when combined with our removable rider's backrest.
Corbin's Stinger saddle is available for standard FLH and FLT models as well, but this one is designed specifically for the CVO Screaming Eagle model Electra-Glide. Harley-Davidson refers to this model as the FLHTCSE. The largest difference between our standard Stinger seat model and this one is that the nose area of the saddle has been redesigned to match up perfectly to fit to the chrome tank panel that comes on the Screaming Eagle model. For other FLH/FLT models, please click HERE.
The Stinger is designed to work with any of the removable backrest models available from Corbin for added back support. We prefer the model #02-G shown here for a good combination of support and slick looks. The Corbin backrest is supported by internal hardware so there are no unsightly brackets to clutter up the look of your machine. Installation is simple with a single set-screw under the saddle locking the backrest in place. The backrest angle can be adjusted to your profile quickly and easily without removing the saddle from the bike. With the #02-G backrest in place, this saddle model offers nearly 14 inches of vertical back support!
This saddle was also designed to work in conjunction with one of the Tourpaks available from Harley-Davidson if you choose. We offer two different trunk pads for this setup depending on how much back support you want for your passenger. Our slim line trunk pad mounted up to the low profile Tourpak (commonly called the Pizza Box) is contoured to fit your passenger's back and offer good support even with its thin profile. This model works on the regular and low profile Tourpak and installs easily by drilling four holes in your trunk lid.
The Touring Pad with arms shown here gives your copilot maximum support with the Harley-Davidson Tourpak. This model works especially well on the larger model Tourpak. Our Stinger saddle also works with the luggage rack / Sissy bar available from HD for the bagger models. We offer a contoured pad to work with that combination as well. The Corbin Luggage Rack Pad is ergonomically contoured for good back support without hot spots and mounts to the luggage rack like the stock pad for simple installation. Both of our Trunk Pads and our Luggage Rack Pad come coordinated to your Corbin saddle with a full range of genuine leather options.
The Stinger saddle model is designed mostly as a solo model, so don't expect passengers to be happy on the back for long regardless of the backrest options you provide.
We have a range of leather options to provide a custom look for your bike. In the model shown, we've used Black Faux Baby-Alligator seating, Black Faux-Snake sides and Black Faux-Shark tail. Be sure to take good care of your leather seat with a quality conditioner like Corbin's Saddle Cream. Your seat will look nice for years and show character just like your leather jacket.
Stinger model uses a new key lock mounting system available exclusively from Corbin. Read more about this mounting system by clicking on the 'Specs' Tab.
UNIQUE TECHNOLOGY: The design and manufacture of Corbin products is so unique that Mike Corbin himself holds more than 60 United States Patents! From the process itself to new innovations like the Corbin Glovebox, you can count on highly functional and unique products that work. Corbin products are manufactured under one or more of the following US Patents: 6,848,156 B2; 6,729,516 B2; D 489,540S; 6,655,740 B1; 6,422,648 B1; 5,544,937; 5,608,957; 4,953,911; D545,073S & 6,971,714 B1.
COMFORT CELL® FOAM: The heart of the Corbin saddle! Our exclusive, purpose built foam material, called Comfort Cell, was created to provide a firm, resilient ride that doesn't break down. This means it will support you for long days on the road. Over time, Comfort Cell will break in to provide a personalized fit to your posture and even greater comfort! For the complete story just click the button.
ERGONOMIC SHAPING: A major part of the design criteria of the Corbin saddle is the Ergonomic shape. This means the saddle's foam shape is designed to emulate the curves of the human body. This provides more square inches of body contact and helps to eliminate hot spots. This shaping also neutralizes the seating platform to help curb sliding in the saddle which reduces fatigue. In a nutshell... more comfort for a longer ride! Just click the button at left for an animation that shows how it works.
PATENTED MANUFACTURING TECHNOLOGY: Always an innovator, Mike Corbin invented Integrated Molding technology which is now the process by which all Corbin saddles are made. This process allows extremely tight tolerances and creates a chemical bond between the foam and base material. To see what this is all about, just click the button for More Info
FIBERTECH™ BASEPAN: A purpose built, hybrid material that provides a firm foundation to support the carefully designed ergonomics of the Corbin saddle. Provides a precision fit to every arc and contour of the machine and rides on rubber bumpers to protect your paint. Click on the button at left to learn more...
GENUINE LEATHER: We use leather in all panels of the seat that contact your body. This provides a luxurious ride that breathes with your body. Leather will also break in along with the foam shape to support the personalized fit. Available in a wide range of textures and styles to suit your taste. For more information about leather seating just click away.
CORBIN BACKREST SYSTEM: The first and most versatile removable backrest system available for motorcycles! Corbin's backrests provide added vertical back support and long range comfort. Supported by internal hardware for a very clean look. Backrests adjust to rider's profile for a tailored fit and install or remove easily as desired. A very popular option! Click the button for additional info...
KEY LOCK INSTALLATION: This saddle model uses a new mounting system designed by Corbin to allow installation and removable with a simple key lock. Once the included brackets are installed, the saddle can be removed easily by just inserting and turning the key. Need a demo? Just click the button.
Measurements
Rider Seating: 12.5" wide x 18" long
Approx seat height: 27"
Measurements:
Rider Seating: 12.5" wide x 18" long
Approx seat height: 27"
Latch Pin Installation Instructions: [ Page 1] Saddle installs using a new key latch system. Install the included latch pin into your fender in place of the stock screw. Slip the tongue of the saddle (at the front) into your chassis as you would with the stock seat installation. Then simply lower the rear of the saddle onto the latch pin while turning the key. Release the key and assure saddle is properly latched to pin. To remove saddle, just turn the key to release the lock and remove the saddle.
Show your colors! We usually have a new tee shirt design available every year. For 2007, we are offering the Corbin tee with the official Hollister Rally logo on the Front and our pinstripe design on the back. Available in a variety of styles for men and women! *Show Me*
The authorized biography of Mike Corbin, written by our friend William Carrington. Following the triumphs and trials of a lifetime developing new ideas from motorcycle seats to electric cars. An all American story! *Excerpts*
With the Corbin EZ-Fill adding oil to your primary is simple. Remove the knurled plug from the inspection cover and pour. It looks great and works just as well (a hallmark of Corbin design). Available for: FX, FL Shovelheads, FLST Softails, FXDWG Dyna Wide-Glide, FXR Models, Roadking, Road-Glide and FLH / FLT models. *More Info*
Take good care of your new seat and the seat will take good care of you. Designed to help your leather saddle remain weather resistant and keeps the hide supple. This will allow the leather to break in and age gracefully. Great for boots, gloves & jackets too. Simple rub-in, buff out application. *More Info*
Our most popular backrest model is the perfect blend of form and function. The size looks visually appropriate on most every seat yet is large enough to provide good, sculpted support. Works well in either the rider's or passenger's position. The standard Ovalbac is available with a range of finishing plate options to dress up the rear including chrome! *More Info*
The standard Corbin backrest for years! This model is the same size and shape as the Standard Ovalbac above, but without the hole in the middle. Provides plenty of sculpted back support without looking too big on the bike. Works in both the rider or passenger seating area on virtually all Corbin saddle models. This model also has the option of chrome studs if desired. *More Info*
Like the Standard Ovalbac show above, but with a larger contact area for added support. Works great as a passenger backrest in Dual Touring models. Because of the added width, we do not recommend this model in the front position while carrying a passenger... it may interfere with their legs. Sculpted to provide wide ergonomic support. Offers a variety of finishing plate options to customize the rear (sorry, no chrome). *More Info*
This model is specially designed to be used in the large Dual Touring seats (like HD Baggers) or in Master's Type saddles as found on the Goldwings. Sculpted for extended support both vertically and horizontally, but cut away at the bottom to provide clearance for passenger's legs. A variety of finishing plate options are available to customize the rear. *More Info*
If you want the functionality of a backrest, but also want the smallest appearance possible, this is the backrest model for you. This one is most often used as a rider's backrest in Gunfighter seat models (thus the name). Includes a variety of finishing plate options for the rear. *More Info*
A convenient storage solution that looks great too. Corbin's Glove Box bolts up easily to your #02-S(B) model backrest in place of the rear finishing plate to provide four liters of locking storage. Available in primer or pre-painted. Some color matches are available depending on bike make and model. Comes fully lined too! *More Info*
Corbin makes a variety of trunk pads for your co-pilot's touring pleasure. Each model comes coordinated to your saddle design for a totally integrated look.
* More Info*
Product Questions
If you have a specific question about this product, just drop us a line. We strive to answer all e-mail within one business day.
Post Comments
Of course we want to hear from you! Have some suggestions for us or maybe comments for other riders, send them HERE.
Install Issues?
Having trouble getting your new seat to mount? Check out our Installation Tips page here: Trouble Shooting
Need replacement brackets, hardware or instructions? Write to us here: Tech Support
Hollister Rally INFO
Thinking of making the trek to the Birthplace of the American Biker for the 60th anniversary? You should! Get the latest information on what's happening and where HERE.
Ordering a seat custom or wondering what that inventory model looks like? This is the place to look for all of the current leather and vinyl materials we offer.
Subscribe to the Corbin Times Home Edition. Our weekly newsletter will keep you up to date on new products, new applications, rallies and more. It's fun to read and members are automatically entered for monthly prizes!
Please select cover options from the drop down boxes before adding to cart. We will verify all selections with you before starting production. Have questions? Just click on the "Glossary" or "Materials" button for answers. NOTE: Drop down boxes do not default to descriptions shown on product above.
 
ITEM
DESCRIPTION
PRICE
#HDFLH-STNG4-CVO
Stinger Saddle
$439
Seating Panels
 
Side Panels
 
Welts
 
Tail Section
 
Stitching
 
Special Notes
 
 
 
Unless otherwise noted, saddles may be shown with optional items that are not included. See Accessories Tab for Corbin Backrests, V-Rails & other accessory items.
PLEASE NOTE: Corbin products are designed to fit very close to your bike for a clean look. Due to this, other accessories or options can inhibit proper fit. As an example: Tank Consoles (dashes), ignition modules, exhaust systems, sissy bars, etc. If you have accessories installed on your bike, please let us know so we can verify the fit for you.
SADDLE WARRANTY: Basepan, foam and hardware of the Corbin saddle is warranted to the original owner for life. Cover materials and workmanship are warranted for one year. Product will only be authorized to be shipped back, freight pre-paid, for refining of shape or to replace/rectify defective parts. In cases where the rework requires a new cover, a recover charge will be applied. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization number (RMA).
FIBERGLASS WARRANTY: Structural integrity of Corbin fiberglass components are warranted to the original owner for life. Finish and paint are warranted against manufacturing defect for one year. Damage to product and / or painted surfaces from outside forces or misuse is specifically not covered under warranty. Cash or credit refunds are not available. All goods being handled for customer service consideration must be accompanied by a Corbin receipt and a Return Material Authorization (RMA) number.
EXPORT SALES: USA pricing shown. When products are shipped throughout the world, you will see higher prices because of freight, customs, duty & applicable taxes. Please consider these costs when purchasing Corbin products outside the USA.